Measurement evidence
Synthesis and Characterization of Schiff Base Polymers via Metal Coordination and Its Application in Infrared Stealth Coating · Li X., Zong L., Li W. et al. · Polymers · 2022 · 4563
Reported values remain attached to the sample, method, conditions, extraction quality and source location that produced them.
D230-PyAL-Cu coating · Thin Film
TSS-5X Infrared Emissometer at room temperature; reflectance curves over 2-22 um
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| infrared emissivity over 2-22 um | 0.68 | — | — | Table Exact Reported | 7 · 3.4. Infrared Emissivity · Table 3 |
D230-PyAL coating/polymer · Thin Film
TSS-5X Infrared Emissometer at room temperature; reflectance curves over 2-22 um
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| infrared emissivity over 2-22 um | 0.70 | — | — | Table Exact Reported | 7 · 3.4. Infrared Emissivity · Table 3 |
| average reflectivity over 2-22 um | about 30% | 0.3 fraction | — | Text Approximate | 8 · 3.4. Infrared Emissivity · Figure 5 |
D230-PyAL-Ni coating · Thin Film
TSS-5X Infrared Emissometer at room temperature; reflectance curves over 2-22 um
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| infrared emissivity over 2-22 um | 0.66 | — | — | Table Exact Reported | 7 · 3.4. Infrared Emissivity · Table 3 |
D230-PyAL-Sm coating · Thin Film
TSS-5X Infrared Emissometer at room temperature; reflectance curves over 2-22 um
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| infrared emissivity over 2-22 umMarked as a best value within this paper | 0.58 | — | — | Table Exact Reported | 7 · 3.4. Infrared Emissivity · Table 3 |
| average reflectivity over 2-22 umMarked as a best value within this paper | about 40% | 0.4 fraction | — | Text Approximate | 8 · 3.4. Infrared Emissivity · Figure 5 |
D230-PyAL-Cu coating · Thin Film
Berkovich indenter at 500 nm depth; QCJ impact tester; QTX paint film elasticity tester; grid-drawing adhesion test; tinplate substrates
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| hardness to modulus ratioMarked as a best value within this paper | 0.051 | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
| hardnessMarked as a best value within this paper | 0.230 +/- 0.001 GPa | — | +/- 0.001 GPa | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
| impact resistance | 10 cm | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 6 |
| Young's modulusMarked as a best value within this paper | 4.483 +/- 0.001 GPa | — | +/- 0.001 GPa | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
D230-PyAL coating/polymer · Thin Film
Berkovich indenter at 500 nm depth; QCJ impact tester; QTX paint film elasticity tester; grid-drawing adhesion test; tinplate substrates
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| adhesive force gradeMarked as a best value within this paper | 0 | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 6 |
| flexibility shaft rod surface radiusMarked as a best value within this paper | 0.5 mm | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 6 |
| hardness to modulus ratio | 0.016 | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
| hardness | 0.042 +/- 0.001 GPa | — | +/- 0.001 GPa | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
| impact resistanceMarked as a best value within this paper | 50 cm | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 6 |
| Young's modulus | 2.498 +/- 0.001 GPa | — | +/- 0.001 GPa | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
D230-PyAL-Ni coating · Thin Film
Berkovich indenter at 500 nm depth; QCJ impact tester; QTX paint film elasticity tester; grid-drawing adhesion test; tinplate substrates
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| hardness | 0.203 +/- 0.001 GPa | — | +/- 0.001 GPa | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
| impact resistanceMarked as a best value within this paper | 50 cm | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 6 |
| Young's modulus | 4.343 +/- 0.002 GPa | — | +/- 0.002 GPa | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
D230-PyAL-Sm coating · Thin Film
Berkovich indenter at 500 nm depth; QCJ impact tester; QTX paint film elasticity tester; grid-drawing adhesion test; tinplate substrates
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| flexibility shaft rod surface radiusMarked as a best value within this paper | 0.5 mm | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 6 |
| hardness | 0.195 +/- 0.001 GPa | — | +/- 0.001 GPa | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
| impact resistanceMarked as a best value within this paper | 50 cm | — | — | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 6 |
| Young's modulus | 4.175 +/- 0.003 GPa | — | +/- 0.003 GPa | Table Exact Reported | 10 · 3.6. Mechanical Properties · Table 5 |
D230-PyAL-Cu coating · Thin Film
Mettler TGA/SDTA851, nitrogen, 20 deg C min-1, 30-800 deg C
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| char yield after heating to 800 deg C | 51% | 0.51 fraction | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
| temperature for 10% weight loss | 291 deg C | — | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
| temperature for 5% weight loss | 264 deg C | — | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
D230-PyAL coating/polymer · Thin Film
Mettler TGA/SDTA851, nitrogen, 20 deg C min-1, 30-800 deg C
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| char yield after heating to 800 deg C | 30% | 0.3 fraction | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
| temperature for 10% weight loss | 278 deg C | — | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
| temperature for 5% weight loss | 262 deg C | — | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
D230-PyAL-Ni coating · Thin Film
Mettler TGA/SDTA851, nitrogen, 20 deg C min-1, 30-800 deg C
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| char yield after heating to 800 deg C | 52% | 0.52 fraction | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
| temperature for 10% weight loss | 258 deg C | — | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
| temperature for 5% weight loss | 237 deg C | — | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
D230-PyAL-Sm coating · Thin Film
Mettler TGA/SDTA851, nitrogen, 20 deg C min-1, 30-800 deg C
| Property | Reported value | Normalised value | Uncertainty | Origin and quality | Source |
|---|---|---|---|---|---|
| char yield after heating to 800 deg CMarked as a best value within this paper | 55% | 0.55 fraction | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
| temperature for 10% weight lossMarked as a best value within this paper | 297 deg C | — | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |
| temperature for 5% weight lossMarked as a best value within this paper | 271 deg C | — | — | Table Exact Reported | 9 · 3.5. Thermal Properties · Table 4 |